Roof Coating in Kentwood, MI: Substrates, Prep and Application Guide

An aging commercial roof doesn’t always need a tear-off. When the deck is sound, the insulation is dry, and the existing surface can hold a coating, restoration can extend the roof’s useful life. A reflective finish can also reduce the heat the roof absorbs in summer. The work starts with finding out what condition the roof is in and fixing the defects a coating would otherwise cover up.

Armor Commercial Roofing offers coating and restoration services for commercial and industrial roofs. If you’re considering roof coating in Kentwood, MI, this guide explains which surfaces qualify, why moisture checks come first, how the coating goes on, and what to look for in the warranty.

Commercial roof coating being applied in Kentwood, MI

What Is a Commercial Roof Coating?

A roof coating is applied as a liquid over an existing roof. Depending on the product, it may be rolled or sprayed. Once cured, it forms a continuous protective layer bonded to the surface below. Common options include:

  • Silicone: Often chosen for UV resistance. Some products are rated for standing water, but the coating won’t correct poor drainage.
  • Acrylic: Available in reflective finishes and often suited to roofs that drain well.
  • Urethane: Some formulations are selected for wear and impact resistance, including near rooftop service areas.
  • SEBS and other specialty coatings: May be an option for specific existing surfaces, such as certain asphalt-based roofs, where the manufacturer approves the use.

The right product depends on the existing roof surface, drainage, rooftop traffic, and the requirements of the proposed system.

Suitable Substrates for Roof Coating in Kentwood

The substrate is the surface the coating must bond to. Even if the coating is approved for that material, the existing roof needs to be dry and sound after any repairs.

Metal Roofs

A compatible system can protect metal panels and seal properly prepared seams and fasteners. Loose rust and failing finishes need attention first. Severely corroded panels or failed fasteners may need replacement, and some systems require a primer.

Single-Ply Membranes (TPO, EPDM, PVC)

An aging membrane may be a candidate if the sheet is still sound and seam or flashing defects can be repaired. The proposed coating must be approved for the specific membrane. A manufacturer may require a cleaner, primer, or adhesion test before application.

Modified Bitumen and Built-Up Roofs (BUR)

Some asphalt-based roofs can be coated with an approved system. Loose surfacing and debris need to be removed as specified. Blisters, cracks, and failed laps should be evaluated and repaired before coating.

Spray Polyurethane Foam (SPF)

A protective coating shields roof foam from sunlight. Recoating can renew that protection if the existing foam is dry and sound after any localized repairs.

When a Roof Is Not a Good Candidate

A coating won’t solve widespread wet insulation, a damaged deck, or a membrane that is failing across large areas. Persistent ponding also needs a closer look. If the problem comes from the slope or the structure, a coating alone won’t change how water leaves the roof.

Why Moisture Checks Come First

A roof can look dry from above while the insulation underneath is wet. Coating over wet materials can contribute to blistering and poor adhesion while the moisture continues to damage the roof below.

The right moisture check depends on the roof assembly and what the initial assessment finds:

  • Infrared surveys: A thermal camera can pick up temperature patterns that suggest trapped moisture under suitable conditions. Those patterns need confirmation.
  • Moisture meter surveys: Readings taken across the roof can help narrow down suspect areas when the method is suited to the assembly.
  • Targeted core samples: A sample lets the roofer examine the layers and confirm whether insulation is wet at that location. The opening needs to be patched afterward.

Isolated wet insulation can often be removed and replaced before coating. If moisture is widespread, compare restoration with the cost and scope of replacement. A survey helps show where the roof may need further investigation.

Infrared moisture scan of a commercial roof before coating in Kentwood, MI

Repairs Before the Coating Goes On

Open seams, damaged flashing, and failing fasteners need attention before a coating goes on. Depending on the roof, the repair scope may include:

  • Removing and replacing isolated wet insulation and repairing the membrane above it
  • Repairing open seams, splits, or cracks and reinforcing them where the coating system calls for it
  • Treating corrosion or replacing damaged metal panels and failed fasteners
  • Addressing blisters and damaged layers on asphalt-based roofs
  • Repairing flashing at walls, curbs, and penetrations
  • Clearing or repairing drains and investigating areas where water continues to collect

See Armor’s commercial roof repair services for more on the defects that may need attention before restoration.

Surface Preparation

The coating needs a clean, dry surface it can bond to. Preparation can include washing or other approved cleaning methods, removing loose gravel or failing coating, and allowing the roof to dry. The manufacturer may call for an adhesion test or a compatible primer, depending on the substrate and coating.

In Kentwood, check both the forecast and conditions at the roof surface. The coating instructions set the limits for application temperature, moisture, and the amount of dry weather needed for curing.

How the Roof Coating System Is Applied

Once the roof is repaired and prepared, the product instructions determine the order, coverage rate, and thickness. A coating scope can include:

  1. Detail work: Treat seams, roof openings, fasteners, and flashing with the sealant, fabric, or reinforcing material specified for the system.
  2. Coating application: Roll or spray the specified coat or coats. The number of coats and time between them vary by product.
  3. Thickness checks: Wet film measurements can help verify application thickness while the coating is still wet. Confirm the required finished thickness in the proposal.
  4. Final review: Look for missed areas, thin spots, and incomplete detailing around transitions.

Too little coating can shorten its useful life. Ask for the specified coverage and how it will be checked. For more on the service, see Armor’s commercial roof restoration page.

Product Warranty vs. Expected Service Life

A product warranty covers the items named in the written terms for a stated period. A manufacturer’s system warranty and a contractor’s workmanship warranty may cover different things. Before accepting a quote, check who issues the warranty, whether it covers materials or labor, what maintenance it requires, and how it treats ponding water or physical damage.

Expected service life is how long the coating is likely to protect the roof under actual conditions. It depends on product type, thickness, preparation, drainage, weather exposure, foot traffic, and maintenance. The warranty term by itself doesn’t predict how long the coating will last.

Some systems can be cleaned and recoated later if the underlying roof remains sound and the manufacturer allows it. Inspection findings should guide when recoating makes sense.

Benefits of Roof Coating for Kentwood Buildings

  • Potentially lower project cost when the existing roof is suitable for restoration
  • Less disposal waste and potentially less disruption than a full tear-off
  • A continuous protective surface over properly repaired and detailed areas
  • A reflective finish that can reduce solar heat gain in summer
  • The option to recoat eligible systems later

Why Choose Armor Commercial Roofing

Armor Commercial Roofing offers repair, restoration, and replacement for commercial roofs. Its restoration services cover systems including metal, TPO, EPDM, PVC, modified bitumen, and built-up roofing. A roof assessment can help you compare what a coating would address with what a larger repair or replacement would involve.

Get a Roof Coating Estimate in Kentwood, MI

If your commercial roof is aging but still has a solid base, find out whether it’s a candidate for coating. Contact Armor Commercial Roofing or call (517) 617-6953 to request a free estimate for roof coating in Kentwood, MI.

Frequently Asked Questions

Can a roof coating stop leaks?

A coating can protect a roof after the leak source has been found and repaired. Open seams, failed fasteners, damaged flashing, and wet insulation need their own repairs before coating.

Can you coat a roof with wet insulation?

Wet insulation must be removed and replaced in areas that will be coated. If it extends across a large part of the roof, a larger repair or replacement may be more practical.

What time of year is best for roof coating in Kentwood?

Late spring through early fall often offers more suitable weather. The actual work window depends on the product’s temperature limits, roof surface conditions, and the dry time needed for curing.

How long does a roof coating last?

Service life depends on the product, applied thickness, surface preparation, drainage, and maintenance. Ask about the expected service life of the proposed system and review its written warranty separately.

Is a coating better than roof replacement?

A coating may be more economical when the existing roof is dry and sound after limited repairs. Widespread wet insulation, failing roofing materials, or deck damage can make replacement the better option.